Difference between revisions of "Manually Connect to Wired Network"

From William Paterson University - Information Technology's Wiki
Jump to navigation Jump to search
(Created page with "== Manually Connect to Wired Network == It may be necessary to use these instructions if your browser or computer do not allow you to execute the '''Cisco Network Setup Assis...")
 
m
Line 64: Line 64:
 
       <li>Check '''Connect to these servers:'''
 
       <li>Check '''Connect to these servers:'''
 
       <li>Enter in the following servers, exactly as specified:
 
       <li>Enter in the following servers, exactly as specified:
       <pre>ch-ise-psn1.wpunj.edu;ch-ise-psn2.wpunj.edu;vr-ise-psn1.wpunj.edu;vr-ise-psn2.wpunj.edu</pre>
+
       <pre>ise.wpunj.edu</pre>
       <li>Check Any '''GeoTrust''' Certificates
+
       <li>Check Any '''DigiCert High Assurance EV''' Certificates
 
       <li>Check '''Do Not prompt user to authorize new servers or trusted certification authorities'''
 
       <li>Check '''Do Not prompt user to authorize new servers or trusted certification authorities'''
 
       <li>Change '''Select Authentication Method''' to '''Secured password (EAP-MSCHAP v2)'''
 
       <li>Change '''Select Authentication Method''' to '''Secured password (EAP-MSCHAP v2)'''

Revision as of 15:38, 22 September 2014

Manually Connect to Wired Network

It may be necessary to use these instructions if your browser or computer do not allow you to execute the Cisco Network Setup Assistant.

 

  1. Click on Start > Run and type in services.msc and press enter
    ENS-ISE-Servicesmsc.png
  2. Right click on Wired AutoConfig and left click on Properties.
    ENS-ISE-Services-wiredautoconfig.png
  3. Make the following changes:
    1. Change Startup type to Automatic.
    2. Click Start to start the service
    3. Click OK to save changes
    ENS-ISE-Services-wiredautoconfig-settings.png
  4. Access your Network Interfaces via Control Panel. (Start > Control Panel > Network and Sharing Center > Change adapter settings)
  5. Right Click on your Local Area Connection (Ethernet), left click on properties.
    ENS-ISE-Control panel LocalAreaConnection.png
  6. Left Click on Authentication Tab
    ENS-ISE-LocalAreaConnection Main.png
  7. Make Sure that the following items are checked
    1. Enable IEEE 802.1x authentication
    2. Remember my Credentials for this connection each time I'm logged in
    3. Fallback to unauthorized network access
    ENS-ISE-LocalAreaConnection-Authentication1.png
  8. Make sure that Authentication Method is Microsoft: Protected Eap (PEAP)
  9. Left Click on Additional Settings and make the following configuration changes:
    1. Check Specify Authentication Mode
    2. Select User Authentication
    3. Left Click OK to save settings and return to the Authentication Tab of Local Area Connection Properties
    ENS-ISE-LocalAreaConnection-Authentication3.png
  10. Left Click on Settings and make the following changes:
    1. Check Validate Server Credentials
    2. Check Connect to these servers:
    3. Enter in the following servers, exactly as specified:
      ise.wpunj.edu
    4. Check Any DigiCert High Assurance EV Certificates
    5. Check Do Not prompt user to authorize new servers or trusted certification authorities
    6. Change Select Authentication Method to Secured password (EAP-MSCHAP v2)
    7. Click Configure and uncheck Automatically use my Windows logon name and password (and domain if any) and click OK.
      ENS-ISE-EAP MSCHAPv2.PNG
    ENS-ISE-LocalAreaConnection-Peap.PNG
  11. Click OK on all open dialog boxes in order to save settings and apply.
  12. You should now be prompted via Windows to enter your a Username / Password. Please Enter your WP Connect Username and Password.


You should now have full access to the WPUNJNet.


Network Services