William Paterson University - Information Technology's Wiki - User contributions [en]

File:ENS-ISE-LocalAreaConnection-Peap.PNG

2014-09-22T19:40:30Z

Tavoularisr: Tavoularisr uploaded a new version of "File:ENS-ISE-LocalAreaConnection-Peap.PNG"

Manually Connect to Wired Network

2014-09-22T19:39:10Z

Tavoularisr:

== Manually Connect to Wired Network ==

It may be necessary to use these instructions if your browser or computer do not allow you to execute the '''Cisco Network Setup Assistant'''.

<p> </p>
<ol>
<li>Click on '''Start > Run''' and type in '''services.msc''' and press enter
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:ENS-ISE-Servicesmsc.png|center|450px]]
</div>

<li>Right click on '''Wired AutoConfig''' and left click on '''Properties'''.

<div class="toccolours mw-collapsible mw-collapsed" style="width:750px">
[[Image:ENS-ISE-Services-wiredautoconfig.png|center|750px]]
</div>

<li>Make the following changes:
<ol>
<li>Change '''Startup type''' to '''Automatic'''.
<li>Click '''Start''' to start the service
<li>Click '''OK''' to save changes
</ol>

<div class="toccolours mw-collapsible mw-collapsed" style="width:350px">
[[Image:ENS-ISE-Services-wiredautoconfig-settings.png|center|350px]]
</div>

<li>Access your Network Interfaces via Control Panel. ('''Start > Control Panel > Network and Sharing Center > Change adapter settings''')
<li>Right Click on your Local Area Connection (Ethernet), left click on properties.
<div class="toccolours mw-collapsible mw-collapsed" style="width:300px">
[[Image:ENS-ISE-Control panel LocalAreaConnection.png|center|300px]]
</div>

<li>Left Click on '''Authentication''' Tab
<div class="toccolours mw-collapsible mw-collapsed" style="width:350px">
[[Image:ENS-ISE-LocalAreaConnection Main.png|center|350px]]
</div>

<li>Make Sure that the following items are checked
<ol>
<li>'''Enable IEEE 802.1x authentication'''
<li>'''Remember my Credentials for this connection each time I'm logged in'''
<li>'''Fallback to unauthorized network access'''
</ol>
<div class="toccolours mw-collapsible mw-collapsed" style="width:400px">
[[Image:ENS-ISE-LocalAreaConnection-Authentication1.png|center|400px]]
</div>
<li>Make sure that '''Authentication Method''' is '''Microsoft: Protected Eap (PEAP)'''

<li>Left Click on '''Additional Settings''' and make the following configuration changes:
<ol>
<li>Check '''Specify Authentication Mode'''
<li>Select '''User Authentication'''
<li>Left Click '''OK''' to save settings and return to the '''Authentication''' Tab of '''Local Area Connection''' Properties
</ol>
<div class="toccolours mw-collapsible mw-collapsed" style="width:350px">
[[Image:ENS-ISE-LocalAreaConnection-Authentication3.png|center|350px]]
</div>

<li>Left Click on '''Settings''' and make the following changes:
<ol>
<li>Check '''Validate Server Credentials'''
<li>Check '''Connect to these servers:'''
<li>Enter in the following servers, exactly as specified:
<pre>ise.wpunj.edu</pre>
<li>Check Any '''DigiCert High Assurance EV Root CA''' Certificates
<li>Check '''Do Not prompt user to authorize new servers or trusted certification authorities'''
<li>Change '''Select Authentication Method''' to '''Secured password (EAP-MSCHAP v2)'''
<li>Click '''Configure''' and uncheck '''Automatically use my Windows logon name and password (and domain if any)''' and click '''OK'''.
<div class="toccolours mw-collapsible mw-collapsed" style="width:250px">
[[Image:ENS-ISE-EAP MSCHAPv2.PNG|center|250px]]
</div>

</ol>
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:ENS-ISE-LocalAreaConnection-Peap.PNG|center|450px]]
</div>
<li>Click OK on all open dialog boxes in order to save settings and apply.
<li>You should now be prompted via Windows to enter your a Username / Password. Please Enter your WP Connect Username and Password.
</ol>

You should now have full access to the WPUNJNet.

[[:Category:Network Services|Network Services]]

Manually Connect to Wired Network

2014-09-22T19:38:34Z

Tavoularisr:

== Manually Connect to Wired Network ==

It may be necessary to use these instructions if your browser or computer do not allow you to execute the '''Cisco Network Setup Assistant'''.

<p> </p>
<ol>
<li>Click on '''Start > Run''' and type in '''services.msc''' and press enter
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:ENS-ISE-Servicesmsc.png|center|450px]]
</div>

<li>Right click on '''Wired AutoConfig''' and left click on '''Properties'''.

<div class="toccolours mw-collapsible mw-collapsed" style="width:750px">
[[Image:ENS-ISE-Services-wiredautoconfig.png|center|750px]]
</div>

<li>Make the following changes:
<ol>
<li>Change '''Startup type''' to '''Automatic'''.
<li>Click '''Start''' to start the service
<li>Click '''OK''' to save changes
</ol>

<div class="toccolours mw-collapsible mw-collapsed" style="width:350px">
[[Image:ENS-ISE-Services-wiredautoconfig-settings.png|center|350px]]
</div>

<li>Access your Network Interfaces via Control Panel. ('''Start > Control Panel > Network and Sharing Center > Change adapter settings''')
<li>Right Click on your Local Area Connection (Ethernet), left click on properties.
<div class="toccolours mw-collapsible mw-collapsed" style="width:300px">
[[Image:ENS-ISE-Control panel LocalAreaConnection.png|center|300px]]
</div>

<li>Left Click on '''Authentication''' Tab
<div class="toccolours mw-collapsible mw-collapsed" style="width:350px">
[[Image:ENS-ISE-LocalAreaConnection Main.png|center|350px]]
</div>

<li>Make Sure that the following items are checked
<ol>
<li>'''Enable IEEE 802.1x authentication'''
<li>'''Remember my Credentials for this connection each time I'm logged in'''
<li>'''Fallback to unauthorized network access'''
</ol>
<div class="toccolours mw-collapsible mw-collapsed" style="width:400px">
[[Image:ENS-ISE-LocalAreaConnection-Authentication1.png|center|400px]]
</div>
<li>Make sure that '''Authentication Method''' is '''Microsoft: Protected Eap (PEAP)'''

<li>Left Click on '''Additional Settings''' and make the following configuration changes:
<ol>
<li>Check '''Specify Authentication Mode'''
<li>Select '''User Authentication'''
<li>Left Click '''OK''' to save settings and return to the '''Authentication''' Tab of '''Local Area Connection''' Properties
</ol>
<div class="toccolours mw-collapsible mw-collapsed" style="width:350px">
[[Image:ENS-ISE-LocalAreaConnection-Authentication3.png|center|350px]]
</div>

<li>Left Click on '''Settings''' and make the following changes:
<ol>
<li>Check '''Validate Server Credentials'''
<li>Check '''Connect to these servers:'''
<li>Enter in the following servers, exactly as specified:
<pre>ise.wpunj.edu</pre>
<li>Check Any '''DigiCert High Assurance EV''' Certificates
<li>Check '''Do Not prompt user to authorize new servers or trusted certification authorities'''
<li>Change '''Select Authentication Method''' to '''Secured password (EAP-MSCHAP v2)'''
<li>Click '''Configure''' and uncheck '''Automatically use my Windows logon name and password (and domain if any)''' and click '''OK'''.
<div class="toccolours mw-collapsible mw-collapsed" style="width:250px">
[[Image:ENS-ISE-EAP MSCHAPv2.PNG|center|250px]]
</div>

</ol>
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:ENS-ISE-LocalAreaConnection-Peap.PNG|center|450px]]
</div>
<li>Click OK on all open dialog boxes in order to save settings and apply.
<li>You should now be prompted via Windows to enter your a Username / Password. Please Enter your WP Connect Username and Password.
</ol>

You should now have full access to the WPUNJNet.

[[:Category:Network Services|Network Services]]

Manually Connect WP Wireless

2014-09-05T14:40:36Z

Tavoularisr:

Manually adding the '''WP Wireless''' Network can fix the following problems
<ul>
<li>Microsoft Windows security warning when connecting to '''WP Wireless'''
<li>Domain Machines trying to logon to '''WP Wireless''' with the local machine credentials
<li>Having to enter username/password twice when connecting to '''WP Wireless'''
</ul>

In order to manually connect to '''WP Wireless'''
<ol>
<li>Manually Add a Wireless Network
<ol>
<li>For '''Windows 7''' clients, go to the '''Network and Sharing Center''' and then click '''Manage Wireless Networks'''
<li>For '''Windows 8''' Clients, go to the '''Network and Sharing Center''' and then click '''Set up a new connection or Network'''
</ol>
<li>Enter '''WP Wireless''' for Network Name
<li>Select '''WPA2-Enterprise''' for Security Type (Windows 7)
<li>Select '''AES''' for Encryption Type
<li>Click Next

<br clear=all>[[Image:Create_Network.png|450px]]<br clear=all>

<li>Click on '''Change Connection Settings'''

<br clear=all>[[Image:Change Connection Settings.png|450px]]<br clear=all>

<li>Click the '''Security''' Tab at the top and click on Advanced Settings. Security Type: WPA2-Enterprise, Encryption: AES
<li>Check '''Specify authentication mode''' and select '''User authentication''' and press ok

<br clear=all>[[Image:Advanced_Settings.PNG|450px]]<br clear=all>

<li>Click on '''Settings''' next to '''Microsoft: Protected EAP (PEAP)
<li>Check '''Verify the Server's identity by validating the certificate'''
<li>Check '''Connect to these servers'''
<li>Specify the following servers: '''ise.wpunj.edu'''
<li>Check any Trusted '''Root Certification Authorities''' from '''DigiCert High Assurance EV Root CA'''
<li>Select '''Don't ask user to authorize new servers or trusted CAs''' from the Notifications before connecting'''
<li>Click on '''Configure''' next to Secured Password (EAP-MSCHAV v2)

<br clear=all>[[Image:PEAP Properties.png|450px]]<br clear=all>

<li>Make sure that the option to automatically use your Windows logon name and password is unchecked

<br clear=all>[[Image:EAP_MSCHAPv2.png|450px]]<br clear=all>

<li>Select OK, save all settings, and attempt to connect.
</ol>

[[:Category:Network Services|Network Services]]

Manually Connect WP Wireless

2014-09-05T14:35:10Z

Tavoularisr:

Manually adding the '''WP Wireless''' Network can fix the following problems
<ul>
<li>Microsoft Windows security warning when connecting to '''WP Wireless'''
<li>Domain Machines trying to logon to '''WP Wireless''' with the local machine credentials
<li>Having to enter username/password twice when connecting to '''WP Wireless'''
</ul>

In order to manually connect to '''WP Wireless'''
<ol>
<li>Manually Add a Wireless Network
<ol>
<li>For '''Windows 7''' clients, go to the '''Network and Sharing Center''' and then click '''Manage Wireless Networks'''
<li>For '''Windows 8''' Clients, go to the '''Network and Sharing Center''' and then click '''Set up a new connection or Network'''
</ol>
<li>Enter '''WP Wireless''' for Network Name
<ol>
<li>Select '''WPA2-Enterprise''' for Security Type (Windows 7)
<li>Select '''802.1x''' for Security Type (Windows 8)
</ol>
<li>Select '''AES''' for Encryption Type
<li>Click Next

<br clear=all>[[Image:Create_Network.png|450px]]<br clear=all>

<li>Click on '''Change Connection Settings'''

<br clear=all>[[Image:Change Connection Settings.png|450px]]<br clear=all>

<li>Click the '''Security''' Tab at the top and click on Advanced Settings. Security Type: WPA2-Enterprise, Encryption: AES
<li>Check '''Specify authentication mode''' and select '''User authentication''' and press ok

<br clear=all>[[Image:Advanced_Settings.PNG|450px]]<br clear=all>

<li>Click on '''Settings''' next to '''Microsoft: Protected EAP (PEAP)
<li>Check '''Verify the Server's identity by validating the certificate'''
<li>Check '''Connect to these servers'''
<li>Specify the following servers: '''ise.wpunj.edu'''
<li>Check any Trusted '''Root Certification Authorities''' from '''DigiCert High Assurance EV Root CA'''
<li>Select '''Don't ask user to authorize new servers or trusted CAs''' from the Notifications before connecting'''
<li>Click on '''Configure''' next to Secured Password (EAP-MSCHAV v2)

<br clear=all>[[Image:PEAP Properties.png|450px]]<br clear=all>

<li>Make sure that the option to automatically use your Windows logon name and password is unchecked

<br clear=all>[[Image:EAP_MSCHAPv2.png|450px]]<br clear=all>

<li>Select OK, save all settings, and attempt to connect.
</ol>

[[:Category:Network Services|Network Services]]

Wireless

2014-07-23T13:58:53Z

Tavoularisr:

[[file:wifi-icon.png|200px|right]]
==Coverage==
William Paterson University provides wireless access into its computing resources utilizing Cisco Aironet wireless equipment. This equipment support all wireless access radios (A,B,G,N) and it utilizes Cisco Clean Access authentication to secure all access.
port and restarted.
==Personal Devices (BYOD)==
Click on [[Getting Started]] and select your operating system to connect to the '''WP Wireless''' Network
==University Machines==
There is no configuration necessary to connect University Machines to the wireless network. If a University Laptop does not connect, follow the instructions below:

* Windows Domain computers need to be rebooted while plugged into an Employee Wired network segment in order to pick up the new GPO Policy
* Windows XP Machines must change the name of the ISE Certificate, as per step 14 of the following instructions: [[Windows XP]]
* MAC Laptop needs to run a manual software update from a wired faculty segment as per Wiki Instructions: [[Mac OS Managed Installs]]

Steps to update GPO on UNV laptop (laptop will not join wireless)
# Plug an Ethernet cable into the laptop's Ethernet jack.
# Restart laptop (it may or may not pick up an IP in the BIOS)
# Wait about a minute on the Ctrl+Alt+Delete (login) screen
# Unplug the Ethernet cable from the laptop
# Have user login
# Check network status in the task bar to make sure it is connected to WP Wireless or WP Wireless 5Ghz
# Verify that internet is working by visiting a website like cnn.com.

[[Category:Network Services]]
[[Category:Mobile]]

Wireless

2014-07-23T13:45:07Z

Tavoularisr:

[[file:wifi-icon.png|200px|right]]
==Coverage==
William Paterson University provides wireless access into its computing resources utilizing Cisco Aironet wireless equipment. This equipment support all wireless access radios (A,B,G,N) and it utilizes Cisco Clean Access authentication to secure all access.
==University Machines==
University Machines do not need to be configured, as they get their settings from the network. If a University Laptop won't connect to the wireless network, it needs to be plugged into an office wired network port and restarted.
==Personal Devices (BYOD)==
Click on [[Getting Started]] and select your operating system to connect to the '''WP Wireless''' Network
==Troubleshooting==
===Certificate Changes===
Generally speaking, Macs and PCs that are a part of the campus domain and that were not operated on campus in the days prior to Friday 1/10/2014 will not be able to connect to any wireless networks such as WP Wireless.
* Windows Domain computers need to be rebooted while plugged into an Employee Wired network segment in order to pick up the new GPO Policy
* Windows XP Machines must change the name of the ISE Certificate, as per step 14 of the following instructions: [[Windows XP]]
* MAC Laptop needs to run a manual software update from a wired faculty segment as per Wiki Instructions: [[Mac OS Managed Installs]]

Steps to update wireless certificate on UNV laptop (laptop will not join wireless)
# Plug an Ethernet cable into the laptop's Ethernet jack.
# Restart laptop (it may or may not pick up an IP in the BIOS)
# Wait about a minute on the Ctrl+Alt+Delete (login) screen
# Unplug the Ethernet cable from the laptop
# Have user login
# Check network status in the task bar to make sure it is connected to WP Wireless or WP Wireless 5Ghz
# Verify that internet is working by visiting a website like cnn.com.

[[Category:Network Services]]
[[Category:Mobile]]

Wireless

2014-07-17T20:48:23Z

Tavoularisr:

[[file:wifi-icon.png|200px|right]]
==Coverage==
William Paterson University provides wireless access into its computing resources utilizing Cisco Aironet wireless equipment. This equipment support all wireless access radios (A,B,G,N) and it utilizes Cisco Clean Access authentication to secure all access.
==Connecting==
Click on [[Getting Started]] and select your operating system to connect to the '''WP Wireless''' Network
==Troubleshooting==
===Certificate Changes===
Generally speaking, Macs and PCs that are a part of the campus domain and that were not operated on campus in the days prior to Friday 1/10/2014 will not be able to connect to any wireless networks such as WP Wireless.
* Windows Domain computers need to be rebooted while plugged into an Employee Wired network segment in order to pick up the new GPO Policy
* Windows XP Machines must change the name of the ISE Certificate, as per step 14 of the following instructions: [[Windows XP]]
* MAC Laptop needs to run a manual software update from a wired faculty segment as per Wiki Instructions: [[Mac OS Managed Installs]]

Steps to update wireless certificate on UNV laptop (laptop will not join wireless)
# Plug an Ethernet cable into the laptop's Ethernet jack.
# Restart laptop (it may or may not pick up an IP in the BIOS)
# Wait about a minute on the Ctrl+Alt+Delete (login) screen
# Unplug the Ethernet cable from the laptop
# Have user login
# Check network status in the task bar to make sure it is connected to WP Wireless or WP Wireless 5Ghz
# Verify that internet is working by visiting a website like cnn.com.

[[Category:Network Services]]
[[Category:Mobile]]

WP Wireless for Mac OS

2014-01-08T14:51:01Z

Tavoularisr:

In order to log into the WP Wireless network at the login window on a university supplied Mac OS laptop you need to have a wireless profile installed. Once installed you will see the following at your login window:

[[File:WP Wireless Login Window.JPG|WP Wireless Login Window.JPG]]

You will only see this menu if your Wifi is on. By default the Wi-Fi option will show up. When you are campus you should use that. When you are at home you should select "None" so that the computer does not waste time trying to connect to the university wireless networks.

If you have a university owned laptop and have not seen an update for the WPU ISE Wireless Profile, please run [[Mac OS Managed Installs & Updates]] from the Utilities folder.

If you are unable to connect to the university wireless to do this update, please connect your laptop to a wired network cable and then retry the Managed Software Update. Alaternately you may do this update from home with a VPN connection. Please beware that during installation your home wireless connection may be disrupted.

[[Category:Apple]]
[[Category:Helpdesk]]

File:PEAP Properties.png

2014-01-07T19:50:13Z

Tavoularisr: Tavoularisr uploaded a new version of "File:PEAP Properties.png"

Manually Connect WP Wireless

2014-01-07T19:48:38Z

Tavoularisr:

Manually adding the '''WP Wireless''' Network can fix the following problems
<ul>
<li>Microsoft Windows security warning when connecting to '''WP Wireless'''
<li>Domain Machines trying to logon to '''WP Wireless''' with the local machine credentials
<li>Having to enter username/password twice when connecting to '''WP Wireless'''
</ul>

In order to manually connect to '''WP Wireless'''
<ol>
<li>Manually Add a Wireless Network
<ol>
<li>For '''Windows 7''' clients, go to the '''Network and Sharing Center''' and then click '''Manage Wireless Networks'''
<li>For '''Windows 8''' Clients, go to the '''Network and Sharing Center''' and then click '''Set up a new connection or Network'''
</ol>
<li>Enter '''WP Wireless''' for Network Name
<li>Select '''WPA2-Enterprise''' for Security Type
<li>Select '''AES''' for Encryption Type
<li>Click Next
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:Create_Network.png|center|450px]]
</div>
<li>Click on '''Change Connection Settings'''
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:Change Connection Settings.png|center|450px]]
</div>
<li>Click the '''Security''' Tab at the top and click on Advanced Settings
<div class="toccolours mw-collapsible mw-collapsed" style="width:470px">
[[Image:Security_Tab.png|center|470px]]
</div>
<li>Check '''Specify authentication mode''' and select '''User authentication''' and press ok
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:Advanced_Settings.PNG|center|450px]]
</div>
<li>Click on '''Settings''' next to '''Microsoft: Protected EAP (PEAP)
<li>Check '''Verify the Server's identity by validating the certificate'''
<li>Check '''Connect to these servers'''
<li>Specify the following servers: '''ise.wpunj.edu'''
<li>Check any Trusted '''Root Certification Authorities''' from '''DigiCert High Assurance EV Root CA'''
<li>Select '''Don't ask user to authorize new servers or trusted CAs''' from the Notifications before connecting'''
<li>Click on '''Configure''' next to Secured Password (EAP-MSCHAV v2)
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:PEAP Properties.png|center|450px]]
</div>
<li>Make sure that the option to automatically use your Windows logon name and password is unchecked
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:EAP_MSCHAPv2.png|center|450px]]
</div>
<li>Select OK, save all settings, and attempt to connect.
</ol>

[[:Category:Network Services|Network Services]]

Google Chromebook

2013-10-03T18:34:32Z

Tavoularisr: Created page with " <ol> <li>Select WP Wireless [or WP Wireless (5Ghz)] from the available Wireless Networks <li>Configure the Following Settings: <ul> <li>SSID: WP Wireless <li>EAP Method: PEAP..."

<ol>
<li>Select WP Wireless [or WP Wireless (5Ghz)] from the available Wireless Networks
<li>Configure the Following Settings:
<ul>
<li>SSID: WP Wireless
<li>EAP Method: PEAP
<li>Phase 2 authentication: MSCHAPV2
<li>Identity: Your WP Connect Username
<li>Password: Your WP Connect password
<li>Anonymous identity: (Leave this field Blank)</ul>

<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:Chromebook-advancedoptions.jpg |center|450px]]
</div>

<li>Click Connect
<li>Accept any Certificate Warnings
<li>You should now have internet access. Contact [https://help.wpunj.edu/helpdesk/ Help Desk Request] if you cannot connect.

</ol>

[[:Category:Network Services|Network Services]]

File:Chromebook-advancedoptions.jpg

2013-10-03T18:32:13Z

Tavoularisr:

Kindle Fire Wireless

2013-09-12T15:35:27Z

Tavoularisr:

<ol>
<li>Select Settings
<li>Select WiFi
<li>Select WP Wireless from the available Wireless Networks
<li>Configure the Following Settings:
<ul>
<li>Security: 802.1x EAP
<li>EAP Method: PEAP
<li>Phase 2 authentication: MSCHAPV2
<li>Identity: Your WP Connect Username
<li>Anonymous identity: (Leave this field Blank)
<li>Password: Your WP Connect password</ul>

<li>Click Connect
<li>Accept any Certificate Warnings
<li>You should now have internet access. Contact [https://help.wpunj.edu/helpdesk/ Help Desk Request] if you cannot connect.

</ol>

[[:Category:Network Services|Network Services]]

Kindle Fire Wireless

2013-09-10T14:55:44Z

Tavoularisr: Created page with "<ol> <li>Select Settings <li>Select WiFi <li>Select WP Wireless from the available Wireless Networks <li>Configure the Following Settings: <ul> <li>Security: 802.1x EAP <li>EA..."

<ol>
<li>Select Settings
<li>Select WiFi
<li>Select WP Wireless from the available Wireless Networks
<li>Configure the Following Settings:
<ul>
<li>Security: 802.1x EAP
<li>EAP Method: PEAP
<li>Phase 2 authentication: MSCHAPV2
<li>Identity: Your WP Connect Username
<li>Anonymous identity: (Leave this field Blank)
<li>Password: Your WP Connect password</ul>

<div class="toccolours mw-collapsible mw-collapsed" style="width:300px">
[[Image:Android-settings 300x500.jpg |center|300px]]
</div>

<li>Click Connect
<li>Accept any Certificate Warnings
<li>You should now have internet access. Contact [https://help.wpunj.edu/helpdesk/ Help Desk Request] if you cannot connect.

</ol>

[[:Category:Network Services|Network Services]]

Getting Started: Wired

2013-09-04T15:55:40Z

Tavoularisr: /* Getting Started: Wired */

== Getting Started: Wired ==

If these instructions do not work, please follow the instructions to [[Manually Connect to Wired Network]]

<p> </p>
<ol>
<li>Plug in machine to your assigned network port. The port should go up and you should obtain an IP address (149.151.x.x). If you are unable to obtain an IP address, please report the problem to ResNet or fill in the smartphone mobile '''[https://webapps.wpunj.edu/misc/resnet/ Report a Problem]''' form so that they can verify your network jack connectivity.

<li>Check your TCP/IP settings to ensure the "Obtain IP address automatically" and "Obtain DNS server address automatically" are checked.

<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:wireless-1.jpg|center|450px]]
</div>

<li>Open Internet Explorer (Firefox and Chrome will not work for provisioning). A captive portal provisioning page will open automatically.

<div class="toccolours mw-collapsible mw-collapsed" style="width:575px">
[[Image:ENS-ISE-Portal-Login.PNG|center]]
</div>

<li>Type in your wpconnect username and password.

<li>Type in a name for your device and click on "Register"

<div class="toccolours mw-collapsible mw-collapsed" style="width:575px">
[[Image:ENS-ISE-Portal-Register.PNG|center]]
</div>

<li>Download and install the '''Cisco Network Setup Assistant'''. Accept any certificate or windows prompts.

<li>If prompted, type in your WPConnect password, otherwise, just click '''start'''. Accept any certificate or windows prompts.

<div class="toccolours mw-collapsible mw-collapsed" style="width:575px">
[[Image:ENS-ISE-CNA.PNG|center]]
</div>

<li>Once the '''Cisco Network Setup Assistant''' completes configuration, your device should have full internet access

<div class="toccolours mw-collapsible mw-collapsed" style="width:575px">
[[Image:ENS-ISE-CNA-Successful.PNG|center]]
</div>

</ol>

You should now have full access to the WPUNJNet.

[[:Category:Network Services|Network Services]]

Wireless Frequently Asked Questions

2013-09-04T15:30:39Z

Tavoularisr:

===Why do I keep getting redirected to the Guest portal?===
You are connected to 'WP Wireless-Guest' which is only for Gaming Consoles, Sponsored Guests of the University, or devices that are not capable of 802.1x. You must connect to the '''WP Wireless''' SSID [[Getting_Started| using these instructions]]
===Why do I keep getting redirected even though I joined the 'WP Wireless?' SSID===
Your device may prefer to connect to '''WP Wireless-Guest''' over '''WP Wireless''' since it knows how to connect to both networks. Once configured to connect to WP Wireless, you must "forget" '''WP Wireless-Guest''' on your device.

===Why do I see a warning that I am connecting to an unsecure network?===
This is due to an incomplete wireless configuration of your device. Follow the instructions to [[Manually_Connect_WP_Wireless| Manually Connect to WP Wireless]]. The specific steps to correct this issue are 9-15.
===Why do I have to log in twice when connecting to WP Wireless?===
This is due to an incomplete wireless configuration of your device. Follow the instructions to [[Manually_Connect_WP_Wireless| Manually Connect to WP Wireless]]. The specific step to correct this is step 8.
===Why does WP Wireless try to use my Windows username and password?===
This is due to an incomplete wireless configuration of your device. Follow the instructions to [[Manually_Connect_WP_Wireless| Manually Connect to WP Wireless]]. The specific step to correct this is step 16.
===Why can't I save I tried to manually change the WP Wireless settings but they aren't getting saved and I cannot connect===
This is usually due to a third party software managing your wireless (Intel Proset, HP or Dell wireless management software, etc). You need to make the equivalent changes through this software, or disable the software and manage your wireless through windows.
===How do I configure a device that isn't 802.1x compatible? ===
Devices that are not 802.1x compatible can be added to the [http://www.wpunj.edu/mydevices My Devices] portal, and then connect to the '''WP Wireless-Guest''' Network.

Wireless Frequently Asked Questions

2013-09-04T15:30:18Z

Tavoularisr: /* Why do I keep getting redirected even though I joined the 'WP Wireless?' SSID */

===Why do I keep getting redirected to the Guest portal?===
You are connected to 'WP Guest' which is only for Gaming Consoles, Sponsored Guests of the University, or devices that are not capable of 802.1x. You must connect to the '''WP Wireless''' SSID [[Getting_Started| using these instructions]]
===Why do I keep getting redirected even though I joined the 'WP Wireless?' SSID===
Your device may prefer to connect to '''WP Guest''' over '''WP Wireless''' since it knows how to connect to both networks. Once configured to connect to WP Wireless, you must "forget" '''WP Wireless-Guest''' on your device.

===Why do I see a warning that I am connecting to an unsecure network?===
This is due to an incomplete wireless configuration of your device. Follow the instructions to [[Manually_Connect_WP_Wireless| Manually Connect to WP Wireless]]. The specific steps to correct this issue are 9-15.
===Why do I have to log in twice when connecting to WP Wireless?===
This is due to an incomplete wireless configuration of your device. Follow the instructions to [[Manually_Connect_WP_Wireless| Manually Connect to WP Wireless]]. The specific step to correct this is step 8.
===Why does WP Wireless try to use my Windows username and password?===
This is due to an incomplete wireless configuration of your device. Follow the instructions to [[Manually_Connect_WP_Wireless| Manually Connect to WP Wireless]]. The specific step to correct this is step 16.
===Why can't I save I tried to manually change the WP Wireless settings but they aren't getting saved and I cannot connect===
This is usually due to a third party software managing your wireless (Intel Proset, HP or Dell wireless management software, etc). You need to make the equivalent changes through this software, or disable the software and manage your wireless through windows.
===How do I configure a device that isn't 802.1x compatible? ===
Devices that are not 802.1x compatible can be added to the [http://www.wpunj.edu/mydevices My Devices] portal, and then connect to the '''WP Guest''' Network.

Wireless Frequently Asked Questions

2013-09-03T15:20:52Z

Tavoularisr: /* Why do I keep joining 'WP Guest' even after connecting to 'WP Wireless?' */

===Why do I keep getting redirected to the Guest portal?===
You are connected to 'WP Guest' which is only for Gaming Consoles, Sponsored Guests of the University, or devices that are not capable of 802.1x. You must connect to the '''WP Wireless''' SSID [[Getting_Started| using these instructions]]
===Why do I keep getting redirected even though I joined the 'WP Wireless?' SSID===
Your device may prefer to connect to '''WP Guest''' over '''WP Wireless''' since it knows how to connect to both networks. Once configured to connect to WP Wireless, you must "forget" '''WP Guest''' on your device.

===Why do I see a warning that I am connecting to an unsecure network?===
This is due to an incomplete wireless configuration of your device. Follow the instructions to [[Manually_Connect_WP_Wireless| Manually Connect to WP Wireless]]. The specific steps to correct this issue are 9-15.
===Why do I have to log in twice when connecting to WP Wireless?===
This is due to an incomplete wireless configuration of your device. Follow the instructions to [[Manually_Connect_WP_Wireless| Manually Connect to WP Wireless]]. The specific step to correct this is step 8.
===Why does WP Wireless try to use my Windows username and password?===
This is due to an incomplete wireless configuration of your device. Follow the instructions to [[Manually_Connect_WP_Wireless| Manually Connect to WP Wireless]]. The specific step to correct this is step 16.
===Why can't I save I tried to manually change the WP Wireless settings but they aren't getting saved and I cannot connect===
This is usually due to a third party software managing your wireless (Intel Proset, HP or Dell wireless management software, etc). You need to make the equivalent changes through this software, or disable the software and manage your wireless through windows.
===How do I configure a device that isn't 802.1x compatible? ===
Devices that are not 802.1x compatible can be added to the [http://www.wpunj.edu/mydevices My Devices] portal, and then connect to the '''WP Guest''' Network.

Wireless Frequently Asked Questions

2013-09-03T14:59:01Z

Tavoularisr: Created page with "===Why do I keep getting redirected to the Guest portal?=== You are connected to 'WP Guest' which is only for Gaming Consoles, Sponsored Guests of the University, or devices t..."

===Why do I keep getting redirected to the Guest portal?===
You are connected to 'WP Guest' which is only for Gaming Consoles, Sponsored Guests of the University, or devices that are not capable of 802.1x. You must connect to the '''WP Wireless''' SSID [[Getting_Started| using these instructions]]
===Why do I keep joining 'WP Guest' even after connecting to 'WP Wireless?'===
Once configured to connect to WP Wireless, you must "forget" the guest network on your device.
===Why do I see a warning that I am connecting to an unsecure network?===
This is due to an incomplete wireless configuration of your device. Follow the instructions to [[Manually_Connect_WP_Wireless| Manually Connect to WP Wireless]]. The specific steps to correct this issue are 9-15.
===Why do I have to log in twice when connecting to WP Wireless?===
This is due to an incomplete wireless configuration of your device. Follow the instructions to [[Manually_Connect_WP_Wireless| Manually Connect to WP Wireless]]. The specific step to correct this is step 8.
===Why does WP Wireless try to use my Windows username and password?===
This is due to an incomplete wireless configuration of your device. Follow the instructions to [[Manually_Connect_WP_Wireless| Manually Connect to WP Wireless]]. The specific step to correct this is step 16.
===Why can't I save I tried to manually change the WP Wireless settings but they aren't getting saved and I cannot connect===
This is usually due to a third party software managing your wireless (Intel Proset, HP or Dell wireless management software, etc). You need to make the equivalent changes through this software, or disable the software and manage your wireless through windows.
===How do I configure a device that isn't 802.1x compatible? ===
Devices that are not 802.1x compatible can be added to the [http://www.wpunj.edu/mydevices My Devices] portal, and then connect to the '''WP Guest''' Network.

Manually Connect to Wired Network

2013-08-28T17:30:47Z

Tavoularisr: Created page with "== Manually Connect to Wired Network == It may be necessary to use these instructions if your browser or computer do not allow you to execute the '''Cisco Network Setup Assis..."

== Manually Connect to Wired Network ==

It may be necessary to use these instructions if your browser or computer do not allow you to execute the '''Cisco Network Setup Assistant'''.

<p> </p>
<ol>
<li>Click on '''Start > Run''' and type in '''services.msc''' and press enter
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:ENS-ISE-Servicesmsc.png|center|450px]]
</div>

<li>Right click on '''Wired AutoConfig''' and left click on '''Properties'''.

<div class="toccolours mw-collapsible mw-collapsed" style="width:750px">
[[Image:ENS-ISE-Services-wiredautoconfig.png|center|750px]]
</div>

<li>Make the following changes:
<ol>
<li>Change '''Startup type''' to '''Automatic'''.
<li>Click '''Start''' to start the service
<li>Click '''OK''' to save changes
</ol>

<div class="toccolours mw-collapsible mw-collapsed" style="width:350px">
[[Image:ENS-ISE-Services-wiredautoconfig-settings.png|center|350px]]
</div>

<li>Access your Network Interfaces via Control Panel. ('''Start > Control Panel > Network and Sharing Center > Change adapter settings''')
<li>Right Click on your Local Area Connection (Ethernet), left click on properties.
<div class="toccolours mw-collapsible mw-collapsed" style="width:300px">
[[Image:ENS-ISE-Control panel LocalAreaConnection.png|center|300px]]
</div>

<li>Left Click on '''Authentication''' Tab
<div class="toccolours mw-collapsible mw-collapsed" style="width:350px">
[[Image:ENS-ISE-LocalAreaConnection Main.png|center|350px]]
</div>

<li>Make Sure that the following items are checked
<ol>
<li>'''Enable IEEE 802.1x authentication'''
<li>'''Remember my Credentials for this connection each time I'm logged in'''
<li>'''Fallback to unauthorized network access'''
</ol>
<div class="toccolours mw-collapsible mw-collapsed" style="width:400px">
[[Image:ENS-ISE-LocalAreaConnection-Authentication1.png|center|400px]]
</div>
<li>Make sure that '''Authentication Method''' is '''Microsoft: Protected Eap (PEAP)'''

<li>Left Click on '''Additional Settings''' and make the following configuration changes:
<ol>
<li>Check '''Specify Authentication Mode'''
<li>Select '''User Authentication'''
<li>Left Click '''OK''' to save settings and return to the '''Authentication''' Tab of '''Local Area Connection''' Properties
</ol>
<div class="toccolours mw-collapsible mw-collapsed" style="width:350px">
[[Image:ENS-ISE-LocalAreaConnection-Authentication3.png|center|350px]]
</div>

<li>Left Click on '''Settings''' and make the following changes:
<ol>
<li>Check '''Validate Server Credentials'''
<li>Check '''Connect to these servers:'''
<li>Enter in the following servers, exactly as specified:
<pre>ch-ise-psn1.wpunj.edu;ch-ise-psn2.wpunj.edu;vr-ise-psn1.wpunj.edu;vr-ise-psn2.wpunj.edu</pre>
<li>Check Any '''GeoTrust''' Certificates
<li>Check '''Do Not prompt user to authorize new servers or trusted certification authorities'''
<li>Change '''Select Authentication Method''' to '''Secured password (EAP-MSCHAP v2)'''
<li>Click '''Configure''' and uncheck '''Automatically use my Windows logon name and password (and domain if any)''' and click '''OK'''.
<div class="toccolours mw-collapsible mw-collapsed" style="width:250px">
[[Image:ENS-ISE-EAP MSCHAPv2.PNG|center|250px]]
</div>

</ol>
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:ENS-ISE-LocalAreaConnection-Peap.PNG|center|450px]]
</div>
<li>Click OK on all open dialog boxes in order to save settings and apply.
<li>You should now be prompted via Windows to enter your a Username / Password. Please Enter your WP Connect Username and Password.
</ol>

You should now have full access to the WPUNJNet.

[[:Category:Network Services|Network Services]]

Getting Started: Wired

2013-08-28T17:01:07Z

Tavoularisr:

== Getting Started: Wired ==

If these instructions do not work, please follow the instructions to [[Manually Connect to Wired Network]]

<p> </p>
<ol>
<li>Plug in machine to your assigned network port. The port should go up and you should obtain an IP address (149.151.x.x). If you are unable to obtain an IP address, please report the problem to ResNet or fill in the smartphone mobile '''[https://webapps.wpunj.edu/misc/resnet/ Report a Problem]''' form so that they can verify your network jack connectivity.

<li>Check your TCP/IP settings to ensure the "Obtain IP address automatically" and "Obtain DNS server address automatically" are checked.

<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:wireless-1.jpg|center|450px]]
</div>

<li>Open your web browser. A captive portal provisioning page will open automatically.

<div class="toccolours mw-collapsible mw-collapsed" style="width:575px">
[[Image:ENS-ISE-Portal-Login.PNG|center]]
</div>

<li>Type in your wpconnect username and password.

<li>Type in a name for your device and click on "Register"

<div class="toccolours mw-collapsible mw-collapsed" style="width:575px">
[[Image:ENS-ISE-Portal-Register.PNG|center]]
</div>

<li>Download and install the '''Cisco Network Setup Assistant'''. Accept any certificate or windows prompts.

<li>If prompted, type in your WPConnect password, otherwise, just click '''start'''. Accept any certificate or windows prompts.

<div class="toccolours mw-collapsible mw-collapsed" style="width:575px">
[[Image:ENS-ISE-CNA.PNG|center]]
</div>

<li>Once the '''Cisco Network Setup Assistant''' completes configuration, your device should have full internet access

<div class="toccolours mw-collapsible mw-collapsed" style="width:575px">
[[Image:ENS-ISE-CNA-Successful.PNG|center]]
</div>

</ol>

You should now have full access to the WPUNJNet.

[[:Category:Network Services|Network Services]]

Getting Started: Wired

2013-08-28T16:59:20Z

Tavoularisr:

== Getting Started: Wired ==

<p> </p>
<ol>
<li>Plug in machine to your assigned network port. The port should go up and you should obtain an IP address (149.151.x.x). If you are unable to obtain an IP address, please report the problem to ResNet or fill in the smartphone mobile '''[https://webapps.wpunj.edu/misc/resnet/ Report a Problem]''' form so that they can verify your network jack connectivity.

<li>Check your TCP/IP settings to ensure the "Obtain IP address automatically" and "Obtain DNS server address automatically" are checked.

<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:wireless-1.jpg|center|450px]]
</div>

<li>Open your web browser. A captive portal provisioning page will open automatically.

<div class="toccolours mw-collapsible mw-collapsed" style="width:575px">
[[Image:ENS-ISE-Portal-Login.PNG|center]]
</div>

<li>Type in your wpconnect username and password.

<li>Type in a name for your device and click on "Register"

<div class="toccolours mw-collapsible mw-collapsed" style="width:575px">
[[Image:ENS-ISE-Portal-Register.PNG|center]]
</div>

<li>Download and install the '''Cisco Network Setup Assistant'''. Accept any certificate or windows prompts.

<li>If prompted, type in your WPConnect password, otherwise, just click '''start'''. Accept any certificate or windows prompts.

<div class="toccolours mw-collapsible mw-collapsed" style="width:575px">
[[Image:ENS-ISE-CNA.PNG|center]]
</div>

<li>Once the '''Cisco Network Setup Assistant''' completes configuration, your device should have full internet access

<div class="toccolours mw-collapsible mw-collapsed" style="width:575px">
[[Image:ENS-ISE-CNA-Successful.PNG|center]]
</div>

</ol>

You should now have full access to the WPUNJNet.

[[:Category:Network Services|Network Services]]

File:ENS-ISE-Control panel LocalAreaConnection.png

2013-08-28T15:36:12Z

Tavoularisr:

File:ENS-ISE-EAP MSCHAPv2.PNG

2013-08-28T15:36:02Z

Tavoularisr:

File:ENS-ISE-LocalAreaConnection Main.png

2013-08-28T15:35:51Z

Tavoularisr:

File:ENS-ISE-LocalAreaConnection-Authentication1.png

2013-08-28T15:35:40Z

Tavoularisr:

File:ENS-ISE-LocalAreaConnection-Authentication2.png

2013-08-28T15:35:30Z

Tavoularisr:

File:ENS-ISE-LocalAreaConnection-Authentication3.png

2013-08-28T15:35:07Z

Tavoularisr:

File:ENS-ISE-LocalAreaConnection-Peap.PNG

2013-08-28T15:34:45Z

Tavoularisr:

File:ENS-ISE-Servicesmsc.png

2013-08-28T15:34:35Z

Tavoularisr:

File:ENS-ISE-Services-wiredautoconfig.png

2013-08-28T15:33:28Z

Tavoularisr:

File:ENS-ISE-Services-wiredautoconfig-settings.png

2013-08-28T15:33:14Z

Tavoularisr:

File:ENS-ISE-AcceptCertificate.PNG

2013-08-28T15:31:18Z

Tavoularisr:

File:ENS-ISE-AcceptCertificate2.PNG

2013-08-28T15:31:06Z

Tavoularisr:

File:ENS-ISE-CNA.PNG

2013-08-28T15:30:45Z

Tavoularisr:

File:ENS-ISE-CNA-Successful.PNG

2013-08-28T15:30:31Z

Tavoularisr:

File:ENS-ISE-Portal-Login.PNG

2013-08-28T15:30:13Z

Tavoularisr:

File:ENS-ISE-Portal-Register.PNG

2013-08-28T15:29:58Z

Tavoularisr:

File:PEAP Properties.png

2013-06-25T18:23:35Z

Tavoularisr: Tavoularisr uploaded a new version of "File:PEAP Properties.png"

File:PEAP Properties.png

2013-06-25T18:22:50Z

Tavoularisr: Tavoularisr uploaded a new version of "File:PEAP Properties.png"

File:PEAP Properties.png

2013-06-25T18:21:02Z

Tavoularisr: Tavoularisr uploaded a new version of "File:PEAP Properties.png"

Manually Connect WP Wireless

2013-06-25T18:19:58Z

Tavoularisr: Created page with "Manually adding the '''WP Wireless''' Network can fix the following problems <ul> <li>Microsoft Windows security warning when connecting to '''WP Wireless''' <li>Domain Mach..."

Manually adding the '''WP Wireless''' Network can fix the following problems
<ul>
<li>Microsoft Windows security warning when connecting to '''WP Wireless'''
<li>Domain Machines trying to logon to '''WP Wireless''' with the local machine credentials
<li>Having to enter username/password twice when connecting to '''WP Wireless'''
</ul>

In order to manually connect to '''WP Wireless'''
<ol>
<li>Manually Add a Wireless Network
<ol>
<li>For '''Windows 7''' clients, go to the '''Network and Sharing Center''' and then click '''Manage Wireless Networks'''
<li>For '''Windows 8''' Clients, go to the '''Network and Sharing Center''' and then click '''Set up a new connection or Network'''
</ol>
<li>Enter '''WP Wireless''' for Network Name
<li>Select '''WPA2-Enterprise''' for Security Type
<li>Select '''AES''' for Encryption Type
<li>Click Next
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:Create_Network.png|center|450px]]
</div>
<li>Click on '''Change Connection Settings'''
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:Change Connection Settings.png|center|450px]]
</div>
<li>Click the '''Security''' Tab at the top and click on Advanced Settings
<div class="toccolours mw-collapsible mw-collapsed" style="width:470px">
[[Image:Security_Tab.png|center|470px]]
</div>
<li>Check '''Specify authentication mode''' and select '''User authentication''' and press ok
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:Advanced_Settings.PNG|center|450px]]
</div>
<li>Click on '''Settings''' next to '''Microsoft: Protected EAP (PEAP)
<li>Check '''Verify the Server's identity by validating the certificate'''
<li>Check '''Connect to these servers'''
<li>Specify the following servers, separated by a semicolon (no spaces): '''ch-ise-psn1.wpunj.edu;ch-ise-psn2.wpunj.edu;vr-ise-psn1.wpunj.edu;vr-ise-psn2.wpunj.edu'''
<li>Check any Trusted '''Root Certification Authorities''' from '''Geotrust'''
<li>Select '''Don't ask user to authorize new servers or trusted CAs''' from the Notifications before connecting'''
<li>Click on '''Configure''' next to Secured Password (EAP-MSCHAV v2)
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:PEAP Properties.png|center|450px]]
</div>
<li>Make sure that the option to automatically use your Windows logon name and password is unchecked
<div class="toccolours mw-collapsible mw-collapsed" style="width:450px">
[[Image:EAP_MSCHAPv2.png|center|450px]]
</div>
<li>Select OK, save all settings, and attempt to connect.
</ol>

[[:Category:Network Services|Network Services]]

File:Create Network.png

2013-06-25T17:22:01Z

Tavoularisr:

File:Change Connection Settings.png

2013-06-25T17:21:52Z

Tavoularisr:

File:Security Tab.png

2013-06-25T17:21:43Z

Tavoularisr:

File:Advanced Settings.PNG

2013-06-25T17:21:28Z

Tavoularisr:

File:EAP MSCHAPv2.png

2013-06-25T17:21:19Z

Tavoularisr:

File:PEAP Properties.png

2013-06-25T17:21:08Z

Tavoularisr: